VCE • Fan coil units with centrifugal fans AC-motors

Indoor fan coils units for cooling and/or heating with water. The VCE is available in horizontal and vertical versions and with or without casing. In the VCE version with casing and a return grille in the casing, the closed decorative panel at the bottom (for vertical version x5) or at the back (for horizontal version x4) is not included as standard (see versions).

• Ventilclima
  

• For cooling and/or heating by water of hotels, shops, offices,...
  

• Galvanized steel sheet (8/10mm) insulated in all parts in direct contact with the conditioned air

• Insulated condensate tray made of galvanised steel sheet

• Modern decorative cabinet, white RAL9010, made in hot-dip galvanized steel sheet pre-coated with PVC for hight resistance to rust, corrosion,. and grills made of ABS, standard light gray RAL 7035

• Centrifugal fans with statically and dynamically balanced aluminium turbines

• Standard with Single-phase asynchronous electric motor with overload cutout, 6 speeds (3 connected)

• The airfilter of polypropylene is enclosed (EU1) - other filters available upon request

• The heat exhanger are made of copper pipes expanded in aluminum fins, with female fittings and easily accessible air vents, connection left or right following demand

• Also available ECM model with EC motor

• 2 or 4 pipes
• Vertical or horizontal
• Left or right waterconnection
• With or without cabinet
• Extra build-in thermostat
• Thermostat I-10,I-30 or I-50 integrated on the VCE units
• Available with EC motor on request
  

• 12 sizes from 1x to 12x
• 9 versions x1 to x9
• Type x0 = vertical with casing, mounted on the wall
• Type x1 = horizontal with casing, mounted under the ceiling with air intake at the bottom via plinth
• Type x2 = vertical without casing, air inlet at the bottom
• Type x3 = horizontal without casing, air intake at the rear
• Type x4 = horizontal with casing, mounted under the ceiling with air inlet at the bottom the closed (decorative panel at the back on a VCE x4 is on request and not standard)
• Type x5 = vertical with casing, mounted on the floor with air inlet at the front the closed decorative (panel at the bottom on a VCE x5 is on request and not standard)
• Type x7 = vertical without casing, horizontal discharge
• Type x8 = vertical with casing, mounted on the floor with intake grille
• Type x9 = horizontal with casing, mounted under the ceiling with air intake at the rear
• L = Device is on the left: when one is standing in front of the device (vertical) or when the device blows in your face (horizontal), and the water connection is on the left (see downloads - water connection).
• R = Device is on the right: when you are standing in front of the device (vertical) or when the device blows in your face (horizontal), and the water connection is on the right (see downloads - water connection). Selections available upon request

• In and outlet plenum
• Extra driptray
• Feet
• Fresh air louver
• Infra red, wall or inside unit control
• 2 way or 3 way valves (mounted)
• On/off or mudulating motor 230 or 24V on valve
• Condensate pump
• Thermostats for VCE with AC-motors: i-Basic 2, 3 i-Digit 0,1,2,3, I-60, I-70
• With the above thermostats you also need the Power Chart SDP for 3-speed control for the VCE models 8x,9x, 1xx, 11x,12x

VCE-120-L/4p

Explanation

VCE = Centrifugal fan coil unit AC motor

12 = size, see table

0 = vertical - bottom air intake with cabinet, 1 = horizontal - bottom air intake with socle and cabinet, 2 = vertical - air intake bottom air supply vertical without cabinet, 3 = horizontal - air intake back without cabinet, 4 = horizontal - bottom air intake with cabinet, 5 = vertical - front air intake with cabinet, 7 = vertical - bottom air intake and horizontal air supply without cabinet,

8 = vertical - front air intake with socle and cabinet, 9 = horizontal - back air intake with cabinet

L = waterconnection Left, R = waterconnection Right

2P= 2pipes, 4P= 4pipes

Basic unit, EUROVENT certificated, made of galvanized steel (prepared following Zendzimir method), minimal plate 0.8 mm.

The unit includes motor and fan, cool -and/or heating coil, filter, main condensate tray and electrical connection.

Al parts in contact with conditioned air are insulated.

Total insulated main driptray with condensate connection.

Side panels provided of knock-out system for quick and easy connecting of accessories.

On the back provided of small opening for easy installation of the units.

Decorative cabinet has a modern design for all applications and is made in galvanized steel repainted with PVC for high resistance. Grills are made of ABS and control doors are made on the top of the cabinet. basic color is white, on demand other colors are possible. The cabinet is easy to mount or demount by a few screws.

The coils are made of copper tubes and alu fins, provided of a female connection (GAS) and an air nipple. Water connection are left or right and easy be changed on site.

The fans are depending of the size made of different quantity's of turbines. The total of the fan deck (motor and turbine) is dynamic balanced to avoid noise and are low in consumption.

De motors are totally closed, split-condensator type including an overheating safety. Monofasig 230 V / 50 Hz. 6 speeds, 3 speeds are connected or EC motor 0-10V. The motors have slidebearings.

The standard filter of polypropylene with metal frame is EU1. Other filters are possible.