PRODUCTEN
EShop-nummer
Wachtwoord
Welcome to CAIROX BELGIUM
OPTIGO 5 • HVAC controllers
- Controllers
- HVAC Controller
- Heating, cooling, pressure, CO2 or humidity
- DIN rail
- Modulating
- Regin
Accessoires
TG-K3/PT1000 • Duct temperature sensors TG-R5/PT1000 • Room temperature sensors DMD • Differential pressure transmitters with display TRAFO D • Transformators 230 V / 24 V AC DTV • Differential pressure switches CONNECTIONSET • Connection sets for pressure measuring HRTN • Room humidity transmitters DTTH • Duct humidity and temperature transmitter DOX/E • CO2 duct transmitter WOX/E(-D) • CO2 transmitter
Preprogrammed, easy to configure HVAC controller with numeric/graphic background illuminated display
Brand
- Regin
Application
- Temperature control
- CO2 - control
- Humidity control
- Pressure control
- Pressure control with outdoor compensation
Specifications
- Supply voltage: 24 V AC
- 1 analogue input for PT1000
- 1 digital input
- 1 universal input 0 - 10 V DC or digital
- 2 analogue ouputs 0 - 10 V DC
Mounting
- DIN-rail
Accessoires
- Transfo 230 / 24 V AC, type TRAFO 15/D
- Duct temperature sensor, type TG-KH/PT1000 / TG-K3/PT1000
- Room temperature sensor, type TG-R5/PT1000
- Outdoor temperature sensor, type TG-UH3/PT1000
- Pressure transmitter, type DMD
- Pressure switch, type DTV
- CO2 transmitter, type WOX/E(-D) (room) / DOX-E (duct)
- Humidity transmitter, type HRTN (room) / DTTH (duct)
Technical data
- Power consumpition: 6 VA
- IP 20
Function
- Temperature control : the temperature at the sensor is kept at the setpoint value by controlling output signals on AO1 and AO2. A single PI control loop is used. The output AO1 can by configured as : heating / cooling / changeover, the output AO2 can by configured as : not used / cooling / heating / damper
- CO2 control : The CO2-value at the sensor is kept at the setpoint value by controlling the ouput signal AO1. A single PI control loop is used. The output signal will increase when the CO2-value rises above the setpoint value
- Humidity control : The humidity at the sensor is kept at the setpoint value by controlling the output signals on AO1 and AO2. AO1 is used for humidification, AO2 for dehumidification. A single PI loop is used. Humidification and dehumidification can be used simultaneously, a neutral zone can be set between.
- Pressure control : The pressure at the sensor is kept at the setpoint value by controlling output signal AO1. A single PI control loop is used. The output signal will increase when the pressure signal falls below the setpoint value.
- Pressure control with outdoor compensation : The pressure at the sensor is kept at the setpoint value by controlling the output signal on AO1. The setpoint is automatically adjusted according to the outdoor temperature. A single loop PI control is used. The output signal will increase when the pressure signal falls below the setpoint value. the setpoint value follows a settable pressure-to-outdoor temperature relation
Settings
- Temperature setpoints :
- Temperature: -20 to 40°C
- Hysteresis: 0 to 10°C
- P-band: 0 to 99 s
- I-time: 0 to 999 s
- Min-limit damper: 0 to 99%
- Other settings
- CO2 setpoint: 0 to 5000 ppm (settable range correnponds the range of the sensor)
- Humidity setpoint: 0 to 100 %
- Pressure setpoint: 0 to 500 kPa (settable range corresponds the range of the sensor)
- P-band: 0 to 100 %
- I-time: 0 to 990 s
- Outdoor compensation, start: -30 to 50°C
- Pressure at -20°C outdoor temp.: 50 to 500 kPa
Informatie aanvragen. Even geduld a.u.b...
